Microcom 466 User Manual download pdf (Page 66)

NANO-GX User Manual

Page 66

Figure 4-2: CF Card Installation

4.3 Jumper Settings

NOTE:

A jumper is a metal bridge that is used to

close an electrical circuit. It consists of

two metal pins and a small metal clip

(often protected by a plastic cover) that

slides over the pins to connect them.

To CLOSE/SHORT a jumper means

connecting the pins of the jumper with

the plastic clip and to OPEN a jumper

means removing the plastic clip from a

jumper.

Before the NANO-GX is installed in the system, the jumpers must be set in accordance

with the desired configuration. The jumpers on the NANO-GX are listed in

Table 4-1.

Jumper

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 136 137

NANO-GX/GXTC 1
Revision 2
Copyright 3
Table of Contents 4
List of Figures 8
List of Tables 10
BIOS Menus 12
1 Introduction 13
1.2 NANO-GX Overview 15
1.3 Dimensions 17
1.4 Data Flow 19
2 Unpacking 22
2.1 Anti-static Precautions 23
2.2 Unpacking Precautions 23
2.3 Packing List 24
3 Connectors 26
Page 28 28
1 GROUND 30
2 GROUND 30
3 Power IN(+12V) 30
4 Power IN(+12V) 30
PIN NO. DESCRIPTION 31
1 ATX Power button + 31
2 ATX Power button 31
3 PS_ON 32
1 CD Signal (Left) 34
2 Ground 34
3 Ground 34
4 CD Signal (Right) 34
Page 36 36
1 GND 2 VCC5 38
3 Output 0 4 Output 1 38
5 Output 2 6 Output 3 38
7 Input 0 8 Input 1 38
9 Input 2 10 Input 3 38
Page 40 40
3 IR-RX 41
5 IR-TX 41
Page 46 46
1 Reset button + 49
2 Reset button 49
Page 54 54
3.3.1 Ethernet Connector 55
1 TX- 5 N/C 56
2 N/C 6 RX 56
3 TX- 7 N/C 56
4 RX+ 8 N/C 56
1 5V 2 GND 58
3 USBP2N 4 USBP3P 58
5 USBP2P 6 USBP3N 58
7 GND 8 5V 58
4 Installation 60
4.1 Anti-static Precautions 61
4.2.3 Installation Checklist 63
NOTE: 66
Optional 68
4.3.3 CRT/LCD Mode Select 69
JP7 Description 70
1-2 +3.3V LVDS Default 70
2-3 +5V LVDS 70
4.4 Chassis Installation 74
Page 76 76
Page 78 78
4.5.4 SATA Drive Connection 79
Page 80 80
4.5.5 Audio Kit Installation 80
4.7 Software Installation 82
5 Award BIOS 84
5.1 Introduction 85
Page 88 88
5.2 Standard CMOS Features 89
Page 90 90
Page 92 92
5.3 Advanced BIOS Features 94
NTER and the 96
NANO-GX User Manual 100
Page 100 100
5.5 Integrated Peripherals 101
EFAULT) 103
Page 104 104
Page 106 106
Page 109 109
Page 110 110
5.6 Power Management Setup 114
5.7 PnP/PCI Configurations 116
Page 117 117
5.8 PC Health Status 118
Page 119 119
A BIOS Options 120
B Terminology 124
Page 125 125
Page 126 126
Page 127 127
C Digital I/O Interface 128
C.1 Introduction 129
C.2 DIO Connector Pinouts 129
D Watchdog Timer 131
Page 132 132
E Hazardous Materials 134
Disclosure 134
Mercury 135
Page 136 136
Page 137 137

Comments to this Manuals

No comments

Microcom 466 User Manual Page 66

Comments to this Manuals

Related products and manuals for Print & Scan Microcom 466